Saturday, February 2, 2013
Article # 247. 5 Ways to Measure Body Fat Percentage
5 Ways to Measure Body Fat Percentage
Measure Body Fat Percentage #1: Skin Fold Caliper
The “skin fold” method measures your body fat percentage by pinching your fat with your fingers then measuring the thickness with a body fat caliper. The reading is given in millimeters, which you compare to a chart with age and gender to arrive at your body fat percentage. There are many different types of caliper tests, which range from only one site like with the Accumeasure Body Fat Caliper to a 7 site Jackson Pollack Method (some are as high as 12 sites).
• Dependable (when skilled at measuring)
• Variability of measurement (same exact spot needs to used each time)
• More than one-site test requires a skilled fitness professional (I’ve done these thousands of times!)
• For people 35+ pounds (15 kg) overweight, fat may not fit within caliper, so it’s less accurate
Skin Fold is hands down the most effective, accurate, practical method to measure and track your body fat percentage. The self-administered Accumeasure Body Fat Caliper retails for under Rs. 1000/- and is sufficient for most people.
Measure Body Fat Percentage #2: Bioelectric Impedance Analysis
Bioelectric Impedance Analysis, or BIA, determines the electrical impedance, or opposition to the flow of an electric current through the body. Muscle has high water content, and is highly conductive, while fat has lower water content and is not highly conductive. Based on the strength of the impedance along with height and weight metrics, the BIA scale will estimate fat-free body mass and body fat percentage.
Many consumer weight scales like Tanita Body Fat Monitor Scale also come with BIA capabilities, and there are others that require holding the BIA device in your hands. Because the BIA test is based on body water balance, your state of hydration can impact the level of accuracy.
• Very easy to administer
• Inexpensive (most weight scales around $50 or even less have BIA)
• Questionable Accuracy
• Variability of results dependent on hydration level
If you can’t use calipers, this is a far second option. If you have a high body fat percentage (calipers can’t fit around your fat pinch), or you have 35+ pounds to lose, start with BIA, then move to calipers. BIA readings for those with low body fat tend to be completely inaccurate.
Measure Body Fat Percentage #3: Anthropometric
This method uses body circumference measurements to estimate body fat percentages.
• Easy to Administer
• Questionable Accuracy (Body fat is not directly measured)
I would consider this method the least accurate because it doesn’t directly measure body fat (or even attempt to). For example, If you have around 6% body fat using calipers, but according to anthropometric, your body fat is around 11.5%. If you don’t have a BIA scale, or calipers, it can be a decent start.
Measure Body Fat Percentage #4: Hydrostatic Weighing
This method is considered the “Gold Standard” (+/- 1.5% error) of body fat measurement that requires being submerged in a specialized tank of water. Because bone and muscle are more dense than water, a person with a larger percentage of fat free mass will weigh more in the water and have a lower percent body fat. Conversely, a large amount of fat mass will make the body lighter in water and have a higher percent body fat.
Accuracy of the reading is contingent upon blowing all the air out of the lungs during pretest screening. The test takes about 20-30 minutes, costs around Rs. 2500 to Rs. 5000, and is available at research labs, universities, or hospitals.
• Very accurate, considered Gold Standard
• Not repeatable (unless you liked repeatedly getting dunked in a tank and spending more)
If you are extremely curious to get the most accurate measure of your body fat percentage, or you are a bodybuilder, or fitness model tracking your progress, Hydrostatic Weighing may make sense. Otherwise, it’s far too impractical.
Measure Body Fat Percentage #5: DEXA Scan
Dual Energy X-ray Absorptiometry known as DEXA is fast becoming the “new” gold standard of body fat measurement because it’s based on a three-compartment model that divides the body into total body mineral, fat-free soft (lean) mass, and fat tissue mass. Hydrostatic Weighing on the other hand only uses a 2 compartment model (fat free mass and fat mass).
DEXA also allows for body fat distribution analysis, so you can figure out with precision how fat is distributed in various parts of your body. In the past, DEXA was only used to measure bone mineral density for ostopenia and osteoporosis in older individuals. The procedure uses a body scanner with low dose x-rays, so it’s completely safe, and takes about 10-20 minutes.
• Very accurate
• Expensive: Around Above 5000 INR (vary from place to place)
• Not repeatable (unless you don’t mind spending more every couple weeks)
Similar to Hydrostatic Weighing, if you are extremely curious to get the most accurate reading of your body fat percentage, or you are a bodybuilder, or fitness model tracking your progress, DEXA may make sense. Otherwise, it’s far too impractical and expensive.
All these methods rely on algorithms to convert a measured parameter into an estimate of body fat percentage, so none of them are perfect. Algorithms have variation based on how the underlying assumptions and formulas apply to different populations.
So what’s the only way to measure body fat with perfect accuracy? Well, cutting open a body and examining the fat, like with a cadaver. Seriously, that’s really the only way to measure body fat percentage most accurately.